Water Restoration Flyer Page 2 Water Restoration Flyer

For more information, visit our website at www.crcindustries.com/ei Click on the Point. Click. Learn! icon to watch a training video on this topic. (215) 674-4300 Customer Service: (800) 272-4620 Technical Assistance: (800) 521-3168 D. Measure Resistance Take Megger readings after equipment has drained. If readings are not up to minimum resistance levels, REPEAT applications. Minimum resistance levels have been set in the IEEE RECOMMENDED PRACTICE FOR TESTING INSULATION RESISTANCE OF ROTATING MACHINERY STD: 43-1974 reaffirmed 1984. It reads as follows: Rm = kV+1 Where Rm = recommended minimum insulation resistance in megohms at 40C of the entire machine winding kV = rated machine terminal to terminal potential in rms kilo volts Minimum resistance is the 1000 ohms/volt + 1 megohm E. Apply a CRC Precision Cleaner When minimum levels have been reached, spray low voltage contacts with a CRC Precision Cleaner No flash point Fast cleaning action for the removal of dirt, light oils and other contaminants Non-conductive and non-corrosive Evaporates quickly, leaves no residue Contains no Class I or Class II ozone depleting chemicals Test on plastics Not for use in California (Use California VOC compliant formula part no. 02240) Contact Cleaner 2000 Precision Cleaner No flash point Fast evaporation, leaves no residue Non-corrosive & non-conductive High dielectric strength of 30,800 volts Contains no Class I or Class II ozone depleting chemicals Test on plastics Not for use in California NT Precision Cleaner No flash point Evaporates rapidly leaving no residue Chemically stable, non-conductive and non-corrosive Low odor Safe on most plastics XT-2000 Precision Cleaner Plastic Safe Evaporates quickly and leaves no residue Effectively removes soil and other contaminants from electronic components Ideal for applications where lower flashpoint solvents can be used QD Contact Cleaner * = Restricted from sale in California Part Number Container Size 02140 16 oz Aerosol 02142 5 Gallon Pail 02143 55 Gallon Drum 03150 16 oz Aerosol 03152 5 Gallon Pail 03153 55 Gallon Drum Part Number Container Size 02205 16 oz Aerosol 02207 5 Gallon Pail 02208 55 Gallon Drum 03205 16 oz Aerosol 03207 5 Gallon Pail 03208 55 Gallon Drum Part Number Container Size 02145 16 oz Aerosol 02147* 5 Gallon Pail 03155 16 oz Aerosol 03157* 5 Gallon Pail Part Number Container Size 02130 16 oz Aerosol 02131* 5 Gallon Pail 02132* 55 Gallon Drum 02133* 16 oz Non-Aerosol Spray Can 03130 16 oz Aerosol 03131* 5 Gallon Pail 03132* 55 Gallon Drum 03134 1 Gallon Bottle = 360 Spray System F. Do Not Energize Until Minimum Resistance Levels are Obtained When Megger readings indicate minimum resistance levels have been reached, energize motors and pumps under "no load" conditions. Allow to run for a period of time to continue drying under normal conditions. When Megger readings return to normal, motors and pumps can be used in normal loaded manner. Tropical storms and hurricanes not only cause extensive damage to electrical and electronic equipment, but their aftermath is devastating and requires an extensive clean-up effort. Maximum performance from power tools is a must. Don't forget additional products available from CRC such as: Chain & Wire Rope Lubricant, Belt Dressing, Air Tool Oil, Bar & Chain Lubricant, Universal 2-Cycle Oil and our wide array of greases. Also, remember CRC's HydroForce line of products for general purpose cleaning, degreasing and disinfecting. I0333-SS 2016 CRC Industries, Inc. CRC, Sta-Lube, K&W, MaryKate and products denoted with and are trademarks or registered trademarks of CRC Industries. * = Restricted from sale in California

Previous Page