Water Restoration Flyer Page 1 Water Restoration Flyer

A. Clean the Equipment To remove dirt, mud, oil, sludge and other contaminants deposited by water, follow these directions as closely as possible. 1. Remove end bells from electric motors and pumps. 2. Remove covers from switch gears and control panels. 3. Flush or spray equipment with generous amounts of clean water and a water based cleaner such as our Hydroforce products to remove any water based contaminants. If possible, dip equipment in a tank or drum of clean water and agitate while submerged. 4. Stand motors and pumps on end and allow to drain. B. Apply a CRC Cleaner or Degreaser To remove oil, grease and sludge contamination not removed by water flushing, dip equipment in a CRC heavy duty degreaser or spray thoroughly. Agitate motors and pumps while submerged. Remove and stand on end. Allow to drain. Spray switch gear and control boxes liberally. Be sure to spray all contaminated areas. Allow to air dry. NOTE: Since CRC heavy duty degreasers are strong cleaners, they may cause crazing or softening of some plastics. It is recommended that a small area be tested before using on plastic parts. C. Apply a CRC Moisture Displacing Lubricant Saturate equipment inside and out. When possible, dip equipment in 2-26 /3-36 . Agitate while submerged. Remove and allow to drain. Spray generously and allow excess to run off. Continue spraying until 2-26 /3-36 run-off is clean and clear. NOTE: Equipment already soaked with water will not be damaged by the use of clean water to flush away dirt, mud and chemical contaminants. Equipment flushed with clean water responds more quickly to treatment with CRC products. Heavy Duty Degreaser No flash or fire point Fast evaporation with no residue Non-corrosive, non-staining and non-conductive High dielectric strength of 39,200 volts High cleaning strength of 105 KB Contains no Class I or Class II Ozone Depleting Chemicals * = Restricted from sale in some states. See SDS for details. Part Number Container Size 03095* 20 oz Aerosol 03095T* 20 oz Aerosol w/ Trigger 03096 1 Gallon Bottle 03097 5 Gallon Pail 03098 55 Gallon Drum Cleans without residue build-up High flashpoint: 180F Non-chlorinated, non-conductive and non-corrosive High dielectric strength of 42,100 volts Contains no Class I or Class II Ozone Depleting Chemicals Zero VOC formula Heavy Duty Degreaser II Part Number Container Size 03120 20 oz Aerosol 03121 1 Gallon Bottle 03122 5 Gallon Pail 03123 55 Gallon Drum High flashpoint: 180F Leaves no residue Non-chlorinated, non-conductive and non-corrosive High dielectric strength of 42,100 volts Contains no Class I or Class II Ozone Depleting Chemicals Zero VOC formula Lectra Clean II Non-Chlorinated Heavy Duty Degreaser Part Number Container Size 02120 20 oz Aerosol 02121 1 Gallon Bottle 02122 5 Gallon Pail 02124 55 Gallon Drum Forms a clear, thin film that lubricates, prevents corrosion, and displaces moisture VOC Compliant Prevents corrosion by displacing moisture and leaving a barrier film Penetrates through corrosion to loosen frozen parts Lubricates without leaving a sticky residue 3-36 Multi-Purpose Lubricant and Corrosion Inhibitor NOTE: 3-36 is green/blue in color. When contaminated with water, it becomes milky colored. Allow to drain. Adequate drainage is a must. Part Number Container Size 03004 6 oz Aerosol 03005 16 oz Aerosol 03006 1 Gallon Bottle 03007 16 oz Trigger Bottle 03009 5 Gallon Pail 03011 55 Gallon Drum Drives out moisture and leaves a thin, long lasting film to protect against corrosion Plastic safe - Will not harm modern plastics, including polycarbonates, ABS and Noryl Prevents corrosion by displacing moisture Restores resistance values and helps stop current leakage Cleans light soils and contaminants 2-26 Multi-Purpose Precision Lubricant Part Number Container Size 02004 6 oz Aerosol 02005 16 oz Aerosol 02006 1 Gallon Bottle 02007 16 oz Trigger Bottle 02009 5 Gallon Pail 02011 55 Gallon Drum Noryl is a registered trademark of General Electric Corporation = 360 Spray System

Next Page